0

Bitumen Testing Equipments

Showing 30 Items
ViewView
  1. Marshal Stability Testing Machine-Digital 4" Dia With PC Interface Software

    Salient features :Alphanumeric 4 - line display indicating Load, displacement, status, peak value of flow and Load.Digital display to measure the load up to 5000Kg/50 KN, Least Count 0.1 kg/0.001KN Displacement resolution : 0.01mm Load and displacement both at the single screen. No need for the flow meter and Proving ring.Only one person needed for test Hassle free operation, no need of TARE.Load cell can also be calibrated using standard reference Panel cut out size 92 x 188 mm.Facility to read in Kg as well as KN Peak hold facility to read load and flow value until reset Auto cutoff at the pre decided load.With safety cut off on lower and upper limit Auto internal calibration facility. (external calibration has to be done after a year)Backlight in the indicator to observe the reading clearly even in the dark.Auto reverse on completion of test Fully powder coated in 2 tone color for aesthetic finish With PC/printer interface with software for direct printout of calculated results (at extra cost)
    Send Inquiry
  2. Rolling Thin Film Oven

    AS PER ASTM D2872; AASHTO T240 ; CNR N.54; EN 12607 - 1
    Send Inquiry
  3. Aggregate Impact Testing Machine

    Complete with a cylindrical cup, 102 mm dia X 50 mm depth, one measure 75 mm dia X 50 mm deep and a tamping rod of circular cross section 10 mm in diameter and 230 mm long, rounded at one end. AS PER IS: 2386 (Part - IV)/ IS 9377
    Send Inquiry
  4. Automatic Compactor for Marshal Test - 6" Dia Specimen

    It is a motor driven mechanical compactor useful for compaction in to 6" dia Marshal moulds. It is fitted with a compaction rammer weighing 10 kg/ 200 gm. with a free fall of 457 mm. The rammer assembly is provided with a ratchet and pawl arrangement to lift it from the top of the test sample. When the rammer reaches the required height the pawl release the rammer which falls freely on test specimen. The release mechanism is connected by an arm moving up and down which is connected to a reduction gear coupled to the motor through another arm. An automatic blow counter fitted to the compactor is used to set the number of blows.
    Send Inquiry
  5. Asphalt Content Oven-(Asphalt Ignition Oven)-(Astm D6307)

    Compliance Standards : ASTM D6307-98 and AASHTO T30. The Asphalt Content/Binder Furnace with internal automatic balance is an environmentally-friendly and cost-effective method for the accurate determination of asphalt content. Ignition method reduces testing time compared to solvent testing methods and automatic operation frees technicians for other tasks. Accurate internal balance monitors weights automatically throughout ignition. Easy operation- simply enter sample weight, calibration factor, load the sample, and push start, when unit beeps at test end, push stop, and sign receipt.
    Send Inquiry
  6. Bitumen Extractor - Motorised With Variable Speed With Digital Rpm Indicator

    SPECIAL MODEL WITH AC MOTOR AND DRIVE : This model facilitates precise speed control and vibration free smooth operation. Speed variation up to 3600 RPM. Complies with following International Standards - ASTM D 2172, AASHTO T 58, T 164. Detailed specification as follows:
    Send Inquiry
  7. Thin Film Oven

    Inner chamber made of S.S. 304 grade & outer of mild steel - powder coated or S.S 304. 65mm Glasswool insulation, double glass built in door to view inside temperature, Temp controlled at 163°C ± 1°C. by means of a calibrated PID based DIGITAL TEMP. INDICATOR CONTROLLER. Inside platform rotated by external motor from 5 to 6 R.P.M. (supplied with cups). To work on 230 V AC single phase.
    Send Inquiry
  8. Automatic Compactor for Marshal Test - 4" Dia Specimen

    It is a motor driven mechanical compactor useful for compaction in to 4" dia Marshal moulds. It is fitted with a compaction rammer weighing 4.5 kg. with a free fall of 457 mm. The rammer assembly is provided with a ratchet and pawl arrangement to lift it from the top of the test sample. When the rammer reaches the required height the pawl release the rammer which falls freely on test specimen. The release mechanism is connected by an arm moving up and down which is connected to a reduction gear coupled to the motor through another arm. An automatic blow counter fitted to the compactor is used to set the number of blows.
    Send Inquiry
  9. Mastic Asphalt Hardness Tester

    Compliance with Following Standards IS : 1195-1968
    Send Inquiry
  10. Apparatus For Distillation of Cut Back Bitumen

    As per IP 27, IS 1213 ASTM D402 method A complete with one distillation flask of 500ml. capacity and one 100 ml. crow receiver (without thermometer) Electrically heated model with Energy regulator. Detailed Specification as follows:
    Send Inquiry
  11. Asphalt Content Gauge

    Compliance Standards : ASTM D6307-98 and AASHTO T30. The Asphalt Content/Binder Furnace with internal automatic balance is an environmentally-friendly and cost-effective method for the accurate determination of asphalt content. Ignition method reduces testing time compared to solvent testing methods and automatic operation frees technicians for other tasks. Accurate internal balance monitors weights automatically throughout ignition. Easy operation- simply enter sample weight, calibration factor, load the sample, and push start, when unit beeps at test end, push stop, and sign receipt.
    Send Inquiry
  12. Low Temperature Waterbath-for Bitumen Penetration Test

    Detailed Specifications as mentioned in the following page.
    Send Inquiry
  13. Saybolt Viscometer With Energy Regulator

    s per ASTM D 88. The apparatus consists of stainless steel bath with oil cup which is centrally placed in a water bath. The bath has a lid which contains a water cooling tube, two handles with two stirring blades, thermometer socket and a straight heater. Stirring is done by turntable arrangement. Supplied without strainer, withdrawal tube and glass wares. Detailed specification as follows:
    Send Inquiry
  14. Ductility Testing Machine (Semi Automatic Model) - (0-100 Mm/min Speed) - (Refrigerated)

    Compliance with Following International Standards As per IS : 1208, ASTM D113. Detailed Specification as follows
    Send Inquiry
  15. Marshal Stability Testing Machine-(4" Dia)-(With Proving Ring and Dial Gauge)

    Complies with following International Standards - ASTM D6927, ASTM D1559. Application - It is used to measure the resistance to plastic flow of cylindrical specimens of bituminous mixture loaded on the lateral surface. Detailed specification as follows:
    Send Inquiry
  16. Buoyancy Balance

    For Water absorption and specific gravity test of aggregates. Detailed specification as mention in following page.
    Send Inquiry
Contact Us

A-1301, BVR Ek, Opp. Hotel Inder Residency, Near Gujarat College, Ellisbridge, Ahmedabad, Gujarat, 380006, India
Phone :91-79-66211234